Comments by "Peter Benson" (@peterbenson3776) on "Wrenching With Kenny" channel.

  1. I saw that fluid reservoir boiling like crazy ..
    17
  2. Its because when you have one of those clips go flying you say “oh jesus”
    8
  3. Some of those plugs are pre gapped and I think the iridiums shouldn’t be touched if I am not nmistaken
    6
  4. Sometimes people mist an engine with water to identify spark leaks
    6
  5. Oh Jesus help me.. find the clip. 😂
    5
  6. You deserve new lights but did you consider rehabbing those lenses?
    5
  7. Another youtube mechanic did a video where the vehicle has similar problems cause by an owner who insisted on stuffing all the fuel in they could fit.
    4
  8. If the garage refuses to work on it doing a half baked job they will get the point. “Take your disaster somewhere else”
    4
  9. How irresponsible to let water in the engine
    4
  10. That should have been fixed by insurance it it was a wreck
    4
  11. Im in northern NY and we need rain. Wells are low foliage is dry.
    4
  12. Display contrast works good for us
    4
  13. Id feel better if I knew the stick was calibrated on one side for transmission
    3
  14. Insert “Bananas” here😂
    3
  15. I like to see you going one direction with the brush
    3
  16. To its credit they said “check wiring” 0 parts
    3
  17. I hand sharpen mine to a fine edge and if I dont hit anything they last a long time. Sharp blades keep grass Healthy with clean cut
    3
  18. Good lord that engine sounds like a threshing machine. McCornick Deering would be proud
    3
  19. Thanks for leaving fuel in the car for mechanic 😂
    3
  20. Lucky save!!
    3
  21. Please send sunshine north !
    3
  22. Oh come on my birthdate is farther down the wheel. 1958 is eons away
    3
  23. I remember some really old trucks with 2speed axles I rode in on the farm had generators ,driver had to race the engine to boost the power to help them shift. Probably had weak old batteries
    2
  24. Good one!
    2
  25. Im scratching my head on this one Kenny. I have a lot of questions.
    2
  26. I’ll use a piece of board to compress the pistons evenly after I pull the caliper.
    2
  27. Will diesel or kerosene work?
    2
  28. I had to have that line changed on my 2015. That was at 38K miles
    2
  29. Several years ago i started delivering car parts working for a friend. I was shocked at how many starters and alternators they were delivering!
    2
  30. What about Wd 45 or carb cleaner?
    2
  31. Did you name the cat? I suggested Ratchet. Lol
    2
  32. Id start with a power flush acts like its not circulating just perking maybe.. my guess thats all.
    2
  33. I just struggled for 2 days removing gasket material from a cast iron fitting ( non automotive) it is a machined face. I kept filing the gasket scraper sharp.
    2
  34. My son has 170+ on his 2007
    2
  35. The corrosion alone was likely going to prevent power enough to flow
    2
  36. Thanks Kenny
    2
  37. Maybe they have a resistor in there to cut down the voltage?
    2
  38. The whole thing needs a bath
    2
  39. Makes perfect sense
    2
  40. My son has a 2007 with afm. He has a dongle to plug in that cancels activation.
    2
  41. Good video!
    2
  42. Cheap fix. Good enough👍
    2
  43. That door is fastened better than most
    2
  44. How many times have you wondered why they cant be greasable?😊
    2
  45. The air in the fuel stream wasnt good either
    2
  46. Im kinda shocked you have time to drive any car 20miles. No one here has time to do that
    2
  47. I believe the numbers on seals and bearings refer to their measurements that would make a good short video..
    2
  48. Up north in the rust belt we use every rust inhibitor we can.
    2
  49. Chunks of silicone migrated to filter?
    2
  50. My 2015 F150 shows no sign of swelling but the factory lug wrench wont begin to fit i went and bought an X wrench to put behind the seat with jack
    2