Comments by "grabir01" (@grabir01) on "Project Farm" channel.

  1. Sea Foam works great at cleaning sludge.
    2
  2. 2 stroke oil helps big time
    2
  3. need to keep throttle wide open when measuring. Also.. Reading will be higher on cold engine. 90 lbs BMEP is not very good for a 4 stroke. Should be more like 130-150 .
    1
  4. myth. Sugar does not dissolve in gas. Now... If you pour sugar inside valve cover, this will end it for the motor. The sugar will melt with the heat and jam up the valves.
    1
  5. 0-30 times would be interesting.
    1
  6. Valvoline is best!
    1
  7. Yes and no. The 4 strokes depend on the transmission. Most transmissions for the 4 strokes are terrible!!
    1
  8. Should have done a torque test. Seeing which one can pull the heaviest load. Typically Briggs makes 3-4 times its torque rating. Honda will be exact. Chinese knock off, not sure.
    1
  9. Surprised you did not include Hot Rims Wheel cleaner as I have not found a better degreaser. Period.
    1
  10. all made in china ccp
    1
  11. Most of my customers use JB
    1
  12. I would like to see if E85 can be used as octane booster in a regular old V8 engine. Since you can no longer get Ethyl high octane which is needed for high compression engines. Can E85 mixed with pump gas in the right amount boost octane?
    1
  13. My Lincoln is almost 30 years old and It still looks and works as new.
    1
  14. Wow!! IS this for real?
    1
  15. FYI. Brock Davidson first in the world to do a 7 sec 1/4 mile at 200 mph did so on a Suzuki Bandit 1200s. He made more power using mid grade fuel .
    1
  16. Any upgrades to your rear diff?
    1
  17.  @ProjectFarm  It was a question. Not a suggestion. Obviously an auto reply.
    1
  18. led better
    1
  19. I normally use energizer. I may try Amazon basics and see..
    1
  20. Not a valid test. Most racers would add 5 moth balls to a 20 gallon tank to increase performance. Most would crush up the moth balls before adding them to aid in dissolving then into the fuel. For his test, he should have 1/4 moth ball and let dissolve , then test.
    1
  21. Bought an old Ford Torino 351c. Sludge city !! Got it running. Sounded a lot like his Truck. Changed oil and added sea foam . Lifter noise went away after time. Drove the car for the next 5 years and finally did a factory spec rebuild since the engine had around 200,000 miles or so.
    1
  22. Anything German requires an engineering degree to operate.
    1
  23. I would like to see the same tests done with proper motor oil. Conventional VS Synthetic.
    1
  24. Silicone are best. Get the PIAA refill in silicone. Cost 15 bucks. Simply replace the rubber with silicone. Done. Not sure if he mentioned it, but with a silicone blade, it coats your glass with its silicone so the water beads up like it has been waxed which helps big time. With such heavy beading of the water, even if your blade quits working, you can still see because of all the beading.
    1
  25. I just cut an removed some panduit zip ties in my garage. I could not break them. Had to cut them. They are over 15 years old.
    1
  26. Milwaukie magnum. Done.
    1
  27. I have no clue where he is finding the LG MJ1 for 3.25 .
    1
  28. No longer using paraffin. But the damage is done.
    1
  29. needed to do the cold test as the catch device will let go when cold on the cheaper ties. This is why I only look for ties with a metal catch.
    1
  30.  @ProjectFarm  YW. A lot of ties work well in warm temps. As soon as they get cold. Zip is right!!
    1
  31. The best zip ties I have ever found are the Panduit zip ties.
    1