Comments by "" (@TXCherokee) on "Rainman Ray's Repairs" channel.

  1. Driving till hits rev limiter over and over?
    2
  2. I got so MAD at that upper hose clap. Dumb design. Few days later bracket came unclamped hose slid back burned hole in from pulley. That’s why I had to buy a new upper hose from Dodge dealer. Came complete with new bracket and unique zip tie
    2
  3. Hi there Ray. Very nice trailer. Plus your dully pulls it easily. DirtyMax working hard. Is there a tow button on end of shifter? My1/2 ton 2001 Chevy did
    2
  4. That Ford SuperDuty pepcock tool is ingenious
    2
  5. Funny. Watching you remove condenser coil. YouTube went to commercial. “ have you ever thought WHY DID THRY DESIGN LIKE THIS? Commercial for Engineering school
    2
  6. That is the most insane design for rear hub assembly I’ve ever seen. So sorry Ray you got involved with this
    2
  7. The blower resistor can’t arc. The battery is disconnected
    2
  8. I see the Green GENERAL Harbor Freight toolbox for the NEW GUY
    2
  9. Keep video coming Ray. Really enjoy. You are the first YouTube I look for every morning
    2
  10. I believe earlier on the PTO output on driver side of Allison was to power hydraulic pump for wrecker bed. But you might adapt a driveshaft to hydraulic pump to run a generator
    2
  11. I think a OIL CATCH CAN is needed for that engine. The EGR is over active. Intake runners coated in oil. Or is that from leaking intake gasket?
    2
  12. Correct. The little sharp tab on connectors got push back. Take ultra tiny flat screwdriver and bend it back out
    2
  13. That is a non stock intake. Factory air box looks nothing like that
    2
  14. You are correct. Pull fuel rail and injectors. Flush install new o rings
    2
  15. My son and I did same rear seal job on 1999 Chevy pickup on garage floor. Fun. Not
    2
  16. Ray. Love some of introduction of past car problems
    2
  17. What a mess. Glad you found it. Wire shorts are the worst. You are “the man” Ray
    2
  18. Thank you Raymond for wishing me a great day. Put a smile on my face and. Hope you as well has a great day
    2
  19. I wonder if the hole is tapered. Wider toward front of car. Maybe the bushing should be pushed in from front side of car. Not a good camera shot
    2
  20. Years ago I changed water pump on pickup had my dog chained up in warehouse. Over night small slope On slab allows little coolant worked way over to dog. Next more he was dead. 😢
    2
  21. Very nice. Banks products are great. My Grand Cherokee Jeep 5.7 Hemi have a Borla touring exhaust
    2
  22. Love your tool box Organization
    2
  23. I may be wrong be any aluminum intake should be “step” torqued
    2
  24. Rich is a smart mechanic. He has a lot of mechanical knowledge as well as you do also Ray
    2
  25. I’ve found self taper screw vibrate get loose over time
    2
  26. This will be a good repair. Lots to fix 😂
    2
  27. Timken Bearing are close to OEM
    2
  28. Sounds like a 5.7 to me. I have the Borla Grand Tour exhaust on Grand Cherokee
    2
  29. There is a company in Houston named Delta Fastener. They sell nuts bolts and screws
    2
  30. Would it be ironic after all of this to discover the rear seal also has to be replaced
    2
  31. I ordered a Craftsman 10 mm gear wrench yesterday to replace a lost 10mm combo wrench. Why do 10mm and 13 mm always get lost
    2
  32. Years ago it was my job to hold the light so Dad could see Know now that’s where I learned early mechanic work
    2
  33. Great Job Raymond. Thinking of physics of welding nut on I believe welding nut to flat washer gave you more leverage 😀
    2
  34. Love seeing palm trees in South Florida
    2
  35. That battery charging fire hazard is very interesting. I have a Mikita battery that has exceeded the charge cycle. 200?
    2
  36.  @mariarusso1325  I’m doing fine. How RU?
    2
  37. Where do you live?
    2
  38.  @mariarusso1325  Houston here
    2
  39.  @mariarusso1325  I am not sure you are real
    2
  40.  @mariarusso1325  so many direct message me are FAKE or SPAM SPAM
    2
  41.  @mariarusso1325  what do you want. This is not the place for chat
    2
  42. I was about to say STOP. YOU DIDN’T ADD OIL 😛
    2
  43. 30° in Houston Texas right now that’s cold for us too
    2
  44. Putting dielectric on spark plug boot is good policy
    2
  45. I agree. Awesome filming and detail about the repairs Love watching your YouTube videos Raymond
    2
  46. I love the sound of Turbo spooling up. Just gives me joy happy 😃 happy
    2
  47. I had to buy a Mopar upper hose once you break that special zip tie. Upper hose will slip back rub on alternator pulley. Very strange design on 2014-2018 grand Cherokee with 5.7
    2
  48. I suggested the same. Was design team on crack
    2
  49. A friend had H2 Hummer with 22” rim. He was 200 miles out of town when front wheel bearing separated. A local shop ripped him off for repair. Bottom line is. Wheels put too much stress on axel
    2
  50. It’s looks like scoop open on back side
    2