Comments by "Citizen" (@rjb6327) on "Rainman Ray's Repairs" channel.

  1. And the missing bolt?
    1
  2. What ever you do, don't tell your boys that the turn around of customer cars is too slow. If that's a break line running on the outside of that bracket, I see some rubbing going on just from the vibration and movement of the frame. BTW: You're saying "sooooooooo" again. Getting to be like the woman you complained about.
    1
  3. So sorry for the lady. How someone can sell something like that to anyone, is beyond me. They should be taken out and shot.
    1
  4. Ray. Your left is his right. So when you point to his right and say left, it can be confusing. 🤨 And remember he's driving yacht. Always nice to see Lauren. I've been saying a bad solenoid from the start.
    1
  5. Always listen to Wife Unit. Always nice to see Wife Unit. 5:55 Something spraying just below the filter?
    1
  6. Accusation: Doesn't matter. You'll charge them what the book says, even if you do it in half the time.
    1
  7. Is the cost worth the horsepower gain?
    1
  8. $300 valve stem? You're in Florida and you were surprised that "someone pulled right out in front of you"?
    1
  9. I think you need a new parts distributor. 🤔🤨 All those new parts and you won't replace the throw out bearing? Part is less than $100.
    1
  10. Isn't one of those negative jumpers supposed to go to an engine ground and not the terminal on the battery?
    1
  11. Even with all the Jeeps you have had to fix in the past, you still say you "really like these boxie SJ's"?
    1
  12. Typical GM. Why should anything be leaking at 98K? Take a look at that paint. Why would anyone buy a GM anything? Ooooooooooooooo Special effects again. 😃 Always nice to see Lauren.
    1
  13. You have to get a hat cam.
    1
  14. Business slow? Troy working for you is like the old days. Work all week and buy all your stuff at the company store. Does he sign his check over to you?
    1
  15. So????? What happened? I think everyone cringed when you put that intake on.
    1
  16. Good job Ray.
    1
  17. Every single video? Excellent! Because, it's always nice to see Lauren.
    1
  18. That "music" you played was really annoying.
    1
  19. Audio cuts out now and then. I was going to mention ventilation, but you seem to have that covered. Before putting anything else in or cutting anymore holes, you should consider where and how you are going to do that. Don't yell at Troy. He's doing what you pay him to do, his job.
    1
  20. Always nice to see Lauren. What did that beautiful flex pipe unit cost? I'm guessing about $600. Just searched it on the net, and found it for sale, at $1325. 😵‍💫 Eric O, to save his customer money, just cut out the bad flex pipe portion and welded in a new one. You're getting really good at breaking off studs. Time to spend some of those profits. You needed those tools when they broke, why are you waiting?
    1
  21. After listening to his truck description, I'm sure this guy won't be back. 😁 He want's to put money into this? This guy doesn't need anything, but a new truck. Always nice to see Lauren. The last "best jeep ever" was during WWII. Tear the truck down for parts and junk the rest.
    1
  22. What a PITA!
    1
  23. You don't think an empty fuel tank, your words 4:23 , has anything to do with it?
    1
  24. You sure about the rubber diaphragm? 😄 Always nice to see Lauren. This is a bugger of a diagnostic.
    1
  25. You need a wider funnel. Just buy the same funnel and cut off the end.
    1
  26. Always nice to see Lauren. You may want to rethink having that radio on. Song royalties.
    1
  27. "mirrow". Isn't that the stuff on the middle of your bones?
    1
  28. Drill a hole and put a toggle switch in.
    1
  29. Sounds like you need a good mechanic. GM strikes again! Could be worse. Could be raining. Oh. Sorry. 😃
    1
  30. Owner could have done that trunk latch himself. 🤔🤨
    1
  31. Did I miss something? Why are you using a creeper and not the lift? What a PITA of a job.
    1
  32. Viewer from the future here. Ray, soon you will leave this dead end job and open up your own place. You won't have to put up with the BS any more.
    1
  33. A lot of Jeeps go through your garage. 🤔🤨 Just because the relay is new, doesn't mean its good.
    1
  34. 0:01 The gathering of the beef. 😁
    1
  35. The guy does all this crap to the car and when he has a problem, he takes it to you? Why not take it to the guy that did all that crap?
    1
  36. Always nice to see Wife Unit.
    1
  37. If the fluid you are putting in is permanent, use the best you have.
    1
  38. Always nice to see the Wife Unit.
    1
  39. Was this before or after you were fired? 😁
    1
  40. You can see the guy who was doing all the work when pushing that van in.
    1
  41. Welcome back from vaca. Hope you, Wife Unit an all the Little Units had a nice relaxing time. Always nice to see Wife Unit, no matter how brief. 15:17 Don't you just love it when you ask for a "personal day" and they ask you why you need one? Glad I don't have to put up with that BS any more.
    1
  42. Been wondering for a while, why is that door always open? Seems to be constantly in the way.
    1
  43. How can a person own a car and not know a damn thing about it.
    1
  44. Business slow? Wife Unit shouldn't have anything to do now. She hired new help for the office and you hired Troy for the shop. 😁 We'll never see her again and it's always nice to see Wife Unit.
    1
  45. That cap will get you every time. OEM big bucks, hence the after market.
    1
  46. It's hard when you actually have to be a mechanic and not rely on computers to tell you whats wrong. Once everybody is driving an electric car, we won't need you any more.
    1
  47. Who taught you how to solder?
    1
  48. Sorry to hear about your son. Hope he heals and feels better.
    1
  49. 17:00 Love it when you speed it up and you go Donald Duck. 😆😆😆
    1
  50. You have a flatbed tow truck and your a mechanic and you're sending it to a junk yard? Nice project truck that could be very useful. You don't seem to be having a good day, today, Ray. All GM had to do was to put an indentation on that tank so the bolt could be taken out, but that would cut into their labor costs. 🤨 If you notice, the ends of the bolts are squared off (hex). You might use that to help you get the bolts out.
    1